eCubed Training Courses | Page 14

Looking to buy in bulk?
Create a request

Switches, Coils, and Overloads (A8006)

This lesson describes switches, coils and overloads, as well as explains the type and operation of switches and overload relays. It will also cover the testing of switches and coils. Participants will learn the proper way to verify that a circuit is de-energized, and how to determine component malfunctions by use of circuit diagrams, manufacturer??s literature and continuity checks.

Professional Development Hours: 1
$60.00

AC Motor Theory (A8011)

This lesson shows and explains how to measure winding insulation resistance and winding resistance. The lesson also describes the major components of AC motors and explains the theory behind permanent magnet motors, three-phase motors, and induction motors.

Professional Development Hours: 1
$23.00

AC Characteristics (A8202)

This lesson covers the basic characteristics of AC circuits including the relationship between voltage and current flow in an AC circuit, the way in which AC voltage is induced, and the cause and effect of inductance and capacitance in AC circuits. The lesson shows and explains how to use a sine wave to interpret changes in AC voltage over time, how to determine the frequency of AC voltage, and how to recognize the effects of inductance and capacitance in AC circuits.

Professional Development Hours: 1
$23.00

Workplace Information Documents (A7204)

This lesson uses typical workplace information documents to provide instruction in reading comprehension and writing skills. Reading skills addressed focus on comprehension of single and multiple paragraphs as well as vocabulary improvement using word structure and context clues. Writing skills focus on organizing ideas into a multiple-paragraph document as well as editing and proofreading techniques. The lesson also explains how to read and interpret charts and graphs.

Professional Development Hours: 1
$60.00

Whole Number Operations (A4301)

This lesson reviews the basic concepts of comparing, rounding, adding, subtracting, multiplying, and dividing whole numbers. It also reviews the steps for solving addition, subtraction, multiplication, and division problems. Participants learn about using estimating techniques and the calculator to solve mathematical problems. Participants also learn about a basic problem-solving strategy that can be applied to solve many mathematical problems.

Professional Development Hours: 1
$60.00

Vibration Analysis (A8302)

This lesson teaches how to monitor vibration and perform a vibration analysis. The lesson interprets various vibration patterns.

Professional Development Hours: 1
$60.00

Troubleshooting Single Loop Control Systems (ATS01)

This lesson describes the systematic approach to troubleshooting and applies that approach to single loop control systems. The lesson explains and demonstrates troubleshooting steps such as verifying that a problem exists, identifying possible causes of the problem, dividing the system to isolate the cause, recommending corrective action, and following up to prevent future problems.

Professional Development Hours: 1
$60.00

Tubing and Threaded Pipe (A8802)

This lesson shows how to cut and bend tubing, use tubing fittings, cut and thread pipe, and use pipefittings. Information on the sequence of steps involved in each procedure, as well as information on using the necessary tools, is also provided.

Professional Development Hours: 1
$60.00

Troubleshooting Multi-loop Control Systems (ATS02)

This lesson discusses the application of the steps for applying the systematic approach to troubleshooting multi-loop control systems. Emphasis is placed on isolating possible causes to the appropriate loop of a multi-loop control system. The lesson applies the basic troubleshooting procedure to ratio, cascade, and feedforward systems.

Professional Development Hours: 1
$60.00

Troubleshooting Distributed Control Systems (ATS03)

This lesson applies a systematic process for identifying, isolating, and correcting process system problems to distributed control systems (DCS). Emphasis is placed on the use of DCS displays as a troubleshooting tool. System graphics such as set point displays, alarm summaries, and trend graphics are included.

Professional Development Hours: 1
$60.00

Troubleshooting Electrical Control Circuits (A8010)

This lesson presents a basic procedure for troubleshooting electrical control circuits. The lesson shows and explains how to gather information about the symptoms, how to verify the symptoms, and how to use the schematic diagram to locate the cause of the problem. The lesson also shows how to perform continuity checks on the circuit and replace any defective components.

Professional Development Hours: 1
$60.00

Troubleshooting Boiler Controls (ABC03)

This lesson teaches how to troubleshoot various boiler control systems. Problems that might be encountered in each phase of boiler operation from startup to shut down will be discussed. The lesson also covers permissive, interlocks, shutdown systems and their associated logic.

Professional Development Hours: 1
$60.00